Hello PDF

Table Saw mm (“) MODEL INSTRUCTION MANUAL SPEC I F ICATIONS 5/8″ Cutting capacities Blade diameter Arbor hole I ” (/4″) 1 N o . ENGLISH (Original instructions) INSTRUCTION MANUAL Table Saw MLT DOUBLE INSULATION IMPORTANT: Read Before Using. 1 ENGLISH. Power tool manuals and free pdf instructions. Find the user manual you need for your tools and more at ManualsOnline. Makita Saw User Manual.

Author: Faura Vogal
Country: New Zealand
Language: English (Spanish)
Genre: Marketing
Published (Last): 4 May 2014
Pages: 474
PDF File Size: 12.52 Mb
ePub File Size: 11.25 Mb
ISBN: 162-6-17535-651-2
Downloads: 43694
Price: Free* [*Free Regsitration Required]
Uploader: Fauzahn

Failure to do so may cause dangerous kickbacks. Switch off saw immediately and disconnect if the blade stops or stalls. Do not use the tool in presence of flammable liquids or gases. The spreader installing location is factoryadjusted. Do not allow them to enter safety guide or inside They are attached by clamps to the back of the table and secured with panhead screws.

Use correctly sharpened saw blades. NEVER use the tool with a faulty blade guard or secure the blade guard with a rope, string, etc. 27008 not cut metal objects such as nails and screws. The riving knife installing location maoita factory-adjusted so that the blade and riving knife will be in a straight line.

Now tighten the lock knob on the rip fence to hold it in place. Lever 1 Install the rip fence so that the fence holder engages with the nearmost guide rail.

Makita 2708 Saw User Manual

Always use a push block or stick when there is a danger that your fingers hand will come close to the blade. The accessories or attachments should be used only makitaa t h e proper and intended manner.

  LATHYRUS CICERA PDF

To know the depth of cut, you must measure it with a ruler. Add to my manuals Add. It should be made from a straight piece of wood thats free of knots or cracks. Use them to make safe, sure cuts without the need for the operator to contact the blade with any part of the body. Use the following saw blade. Push stick 1 2 3 11 4 1.

Makita Manuals and User Guides, Saw Manuals —

To reduce your exposure to these chemicals: Be sure of positive attachment. Never attempt to move the table saw by gripping these holders. The cutting depth indicator tells you the depth of cut by the arrow pointer.

Some dust created from operation contains chemicals known to cause cancer, birth mxnual or other reproductive harm. If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used. Do not carry a plugged-in tool with a finger on the switch.

Inspect extension cords periodically and replace, if damaged. Tighten the hex bolts A with the provided wrench. Then install the rip fence on table and secure lock knob when the rip fence is parallel with the blade. NOWset the saw on top of the assembled stand and secure with 4 hex bolts, flat washers and hex nuts. Use either the rip fence or the miter gauge to position or guide work a t all times. Only use accessory or attachment for its stated purpose. Ripping Ripping i s the lengthwise cutting of a board.

Make sure the blade is not contacting the riving knife or workpiece before the switch is turned on. Thru-sawing operations are those when the blade cuts complete- ly through the work piece as in ripping or cross cutting. The tool should not be used for slotting, rabbetting or grooving.

  FORMULAS LACTEAS PDF

Then simply withdraw the wood. When switching off, do not attempt to stop the blade by pressing on the side of the blade with some object.

If the rip fence is not parallel with the blade, proceed as follows: Page 13 Wood Auxiliary Facing Miter Gauge To prevent long board from wobbling, fit the miter gauge with an auxiliary fence board. This could cause an injury.

Avoid KICKBACKS by keeping the blade sharp, by keeping the rip fence parallel to the blade, by keeping the riving knife and blade guard in place and operating properly, by not releasing Table 1 shows the correct size to use depending on cord length and nameplate ampere rating.

Feed maiita slow as possible when cutting hard material. Loosen the knob on the Always stop the tool and wait for dado head to come to a complete stop. When using an extension cord, be sure to use one heavy enough to amnual the current your product will draw.

Tighten only temporarily the hex socket head bolt on the safety guide installing portion. NEVER wear gloves during operation. NEVER use the fence as a cut-off gauge when cross malita.