Hello PDF

HDPE Pipes: Specifcations. Specification: IS with latest amendments. Material Grade PE All dimension are in mm. OD PN PN 4. PN 6. PN 8. Dinesh Irrigation Private Limited offering Is HDPE Pipes in Jhotwara, Jaipur , Rajasthan. Get contact details, address, map on Indiamart. | ID: We are leading manufacturer of HDPE pipes as per IS The best quality raw materials are procured to offer the pipes meeting the highest quality.

Author: Kajile Faelar
Country: Slovenia
Language: English (Spanish)
Genre: Politics
Published (Last): 1 May 2012
Pages: 459
PDF File Size: 10.80 Mb
ePub File Size: 15.31 Mb
ISBN: 585-3-32958-680-6
Downloads: 76749
Price: Free* [*Free Regsitration Required]
Uploader: Moogukinos

If any of the samples fails in the repeat tests, the typeof pipe shall not be approved.

This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations. The wall thickness shall be measured by a dial vernier or ball ended micrometer. For coiled pipes, however, re-rounding of pipes shall be carried out prior to the measurement of ovality. Page 11, Annex C, clause C In addition the material shall also conform to 5.

Measure the minimum distance between the two marks.

Bentex HDPE Pipe As Per is 4984, Application:Drinking Water

Dhage Alternate Shri M. For guidance and use of random number tables, IS Hdpe Corrugated Subsoil Drainage Pipe. Our entire product range is well-tested. Das Alternate Shri D.

Full text of “IS high density polyethylene pipes for potable water supplies”

In the absence of a random number table the following procedure may be adopted. Hdpe Coil Pipe in Jaipur.

Pipe manufacturers shall obtain a certificate to this effect from the manufacturers of raw material. We offer them in different sizes and diameters and are valued for optimum performance and easy installation. In such cases, the entire circumference of approximately mm long section of pipe shall be divided into pieces measuring approximately mm square.

  COMPONENDO AND DIVIDENDO RULE PDF

Standards are also reviewed periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision. Phadnis Alternate Shri J, R. Hdpe Double Wall Corrugated Pipe. View Contact Call Seller Now. Nature of Business Manufacturer.

Registered under Indian Companies Act Sauce Alternate Shri S. These innovative facilities are in the forefront of product development, which go forward the most careful, vigilant standards of product testing based on national and international standards.

Yadav Alternate Shri G. Nominal diameter Maximum out of square DN of pipe end mm mm 16 to 75 2 90 to 3 to 4 to 5 Above 7 Page 9, Annex Dhpe, A-l — Substitute the following for the existing clause: The manufacturer or the supplier may be asked to improve the design and resubmit the product for type approval.

The basis for the values specified is: Patel Alternate Dr H. Full text of ” IS The lot shall be deemed not to have met these requirements if the number of defectives found in the first sample is greater than or equal to the corresponding rejection numbers given hdpw col 6 of Table 7.

P4 Convener Shri Kanwar A. Sharma Alternate Shri O. A mark shall be scribed on the external surface approximately 50 mm from each end of the test pieces in the axial direction of pipe, in the case of complete section of pipe, the mark shall be scribed around the whole circumference. For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2: Get best deals for coconut.

  DELL T5400 MANUAL PDF

The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.

These stripes shall be coextruded during pipe manufacturing and shall not be more than 0. Phadnis Alternate Shri S. Sunderamoorthy Shri Thimu G. No other reworked or recycled material shall be used.

Nominal Diameter DN 1 16 20 25 32 40 50 63 75 90 PN2. Sinha Alternate Shri O. Part 1 1 Laying and jointing polyethylene PE pipes’. Datt Alternate Shri K. The carbon black content in the material shall be within 2. Pipes for sewer- age and industrial effluents are being covered in a separate standard.

HDPE Pipes – Jain High Density Polyethylene Pipes

The details of conditions under which a licence for the use of the Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian Standards.

If in repeat test, no single failure occurs, the type of pipe under consideration shall be considered eligible for type approval.

NOTE — Considering operational problems, maxi- mum wall thickness of pipes are considered around hdpr mm.