Hello PDF

DMOR Datasheet PDF, DMOR datasheet, DMOR pdf, DMOR pinout, DMOR data, circuit, ic, manual, substitute, parts. Description. The FSDMRE, FSDMRE and FSDMRE are an integrated Pulse Width Modulator (PWM) and. SenseFET specifically designed for. Features. • Optimized for Quasi-Resonant Converter (QRC). • Advanced Burst- Mode Operation for under 1W Standby. Power Consumption. • Pulse-by-Pulse.

Author: Bakazahn Faell
Country: Senegal
Language: English (Spanish)
Genre: Photos
Published (Last): 25 March 2015
Pages: 64
PDF File Size: 11.79 Mb
ePub File Size: 13.83 Mb
ISBN: 426-9-85873-538-8
Downloads: 83288
Price: Free* [*Free Regsitration Required]
Uploader: Tygorg

This pin is internally connected dmo5565r the inverting input of the PWM comparator. In this situation, the protection circuit should be activated in order to protect the SMPS. Then, Vfb climbs up in a datasbeet manner to the over load situation, forcing the preset maximum current to be supplied to the SMPS until the over load protection is activated.

If the voltage of this pin reaches 6. Excessive voltage across the Rsense resistor would lead to incorrect feedback operation in the current mode PWM control. This event typically happens when the input voltage is increased or the output load is decreased.

This device is datashet integrated high voltage power switching regulator which combine an avalanche rugged Sense FET with a current mode PWM control block.

In order to avoid undesired activation of OVP during normal operation, Vcc should be designed to be below 19V. Comparing the feedback voltage with the voltage across the Rsense resistor plus an offset voltage makes it possible to control the switching duty cycle.

DMO565R PDF

Published on Apr View Over load protectiontNormal operation Fault situation Normal operationFigure 6. Maximum practical continuous power in an open frame design at 50C ambient. At startup, an internal high voltage current source supplies the internal bias and charges the external capacitor Cvcc that is connected to the Vcc pin as illustrated in Figure 4.

Then, the FSDMRB continues its normal switching operation and the power is supplied from the auxiliary transformer winding unless Vcc goes below the stop voltage of 8V. If the output consumes beyond this maximum power, the output voltage Vo decreases below the set voltage. During start up, the power is supplied by an internal high voltage current source that is connected to the Vstr pin. Compared with discrete MOSFET and PWM controller solution, it can reduce total cost, component count, size and weight simultaneously increasing efficiency, productivity, and system reliability.

  EKONOMICZNE INSTYTUCJE KAPITALIZMU WILLIAMSON PDF

At this point switching stops and the output voltages start dko565r drop at a rate dependent on standby current load. At the instant the internal Sense FET is turned on, there usually exists a high current spike through the Sense FET, caused dmo565t primary-side capacitance and secondary-side rectifier reverse recovery.

In order to avoid this undesired operation, the over load protection dahasheet is designed to be activated after a specified time to determine whether it is a transient situation or an overload situation. Once Vcc reaches 12V, the internal current source is disabled. Cdbe datasheet pdf – datasheet pdf Cdbe datasheet ratasheet The delay time for shutdown is the time required to charge CB from 2. The PWM controller includes integrated fixed frequency oscillator, under voltage lockout, leading edge blanking LEBoptimized gate driver, internal soft start, temperature compensated precise current sources for a loop compensation and self protection circuitry.

In order to prevent this situation, an over voltage protection OVP circuit is employed. The typical soft start time is 10msec, The pulse width to the power switching device is progressively increased to establish the correct working conditions for transformers, inductors, and capacitors.

DMR Datasheet, PDF – Alldatasheet

Because of the pulse-by-pulse datssheet limit capability, the maximum peak current through the Sense FET is limited, and therefore the maximum input power is restricted with a given input voltage. This causes Vcc to fall.

Free standing with no heat-sink under natural convection. TempBurst Mode Enable Voltage vs. Rockchip RK datasheet V0.

DMOR PDF –

Therefore, the peak value of the current through the Sense FET is limited. SN datasheet – doctor- SN datasheet Author: Datasheet Release Date The feedback voltage then falls and the process repeats. Ql5 datasheet pdf QL5 datasheet, Burst mode operation dmo565rr enables and disables switching of the power Sense FET thereby reducing switching loss in Standby mode.

  BERTRICE SMALL HELLION PDF

TempFeedback Source Current vs. Texas Instruments – Subject: Because more energy than required is provided to the output, the output voltage may exceed the rated voltage before the over load protection is activated, resulting in the breakdown of the devices in the secondary side. As the load decreases, the feedback voltage decreases.

Datasheet DMO565R

SN datasheet – Texas Instruments Documents. It also helps to prevent transformer saturation and reduce the stress on the secondary diode during startup. When the temperature exceeds approximately C, the thermal shutdown is activated.

In this manner, the auto-restart can alternately enable and disable the switching of the power Sense FET until the fault condition is eliminated see Figure 6. In this generation the startup resistor is replaced by an internal high voltage current source. This pin is connected directly to the high voltage DC link.

However, even when the SMPS is in the normal operation, the over load protection circuit can be activated during the load transition. Overload is defined as the load current exceeding a pre-set level due to an unexpected event.

The voltage on the output capacitors is progressively increased with the intention of smoothly establishing the required output voltage. It is designed to drive the transformer directly. This causes the feedback voltage to rise. Qlt datasheet pdf – datasheet pdf QLT datasheet, If the secondary side feedback circuit were to malfunction or a solder defect caused an open in the feedback path, the current through the opto-coupler transistor becomes almost zero.

Assuming that the 0.