Coin Acceptors (Coinco) is a world leader in the design and manufacture of coin mechanisms, bill acceptors, control systems, and vending machines for the. Vantage · BillPro · Bill Recyclers (1/0). Vantage VR6 · Product History (2/0). Bill Acceptors · Coin Changers · iris (2/2). iris Reader · iris Media · Coinco-Office (0/1) . COINCO GLOBAL 2® SERIES O P E R AT I O N AN D S E R V I CE MANUAL TABLE OF CONTENTS SECTION 1: GENERAL INFORMATION.
|Published (Last):||10 February 2012|
|PDF File Size:||5.17 Mb|
|ePub File Size:||5.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
See vending machine manual for details. Free acceptor studs from changer housing. Press C to enter the Sub Address. Repeat steps for the remaining three prices. The vend price must be set to an amount greater than zero for the changer to accept coins in single-price mode.
The far right decimal point will illuminate indicating the selection has been stored. For electromechanical vending machines.
coinco global 2® series operation and service manual |
Use buttons B increase or D decrease to change the value. Remove recessed screw that secures logic board cover and remove cover. Tubes snap in and out of housing for easy customization of your changer Pays out change from self-loading, high capacity change tubes Two motors provide fast, accurate payout. Verify all coins have been routed to the desired tubes.
Refer to the model and serial number whenever you call upon your Coinco Service Centre for information or service. Enter the Display Mode.
Example of setting up user defined coin routing. Replace the cashbox chute by pressing in and up to snap into place.
If coin tube loading door is not locked additional option hand load the four coin tubes see Figure 4. Press A to store the price and return to the Display Mode. The first two digits indicate the week of manufacture; the third and fourth digits indicate the year of manufacture. If the coin changer is being stored or used as a spare, always keep it in its shipping carton when not in use.
These globwl should be removed in the following sequence: For example, Serial Number would indicate that the unit was manufactured in the 15th week of Press C to enter your selection. If the lowest denomination coin is one, the highest vend price setting would be x 1 or ALT options are user programmable.
Coin acceptor of coinco global 2 mdb
Press C to enter Address C Lockable coin loading door allows easy hand-loading of coin tubes while keeping dirt and debris out of the changer. Switch A SW9 Controls whether the escrow feature of the changer is inhibited. Press A again to exit display mode. Wipe the exposed coin ramp and inner surface with a damp cloth, being cautious not to harm the coin stabilizer a thin piece of polyester film. Load the individual coin tube to the float level you want the coin changer to maintain.
Press B to scroll up to C Press A to return to the Address Display. Audit information is retrieved via the Digital Display by performing the following steps: A label indicating the coin changer model number and serial number can be found on the side of the coin changer. Once all twenty-five prices have been set, press A to exit the Display Mode.
Coinco global 2 mdb/other – Global 2 – VendingOutlet Private Webshop
To remove cover, push out and up. Push snap toward top of housing and remove upper tube sense board which will separate from main logic board upon removal. World Headquarters Hunter Avenue St. OFF Vend is pulsed.
After Unpacking After unpacking the unit, inspect it for any possible shipping damage. Repeat steps for the remaining priceline addresses. OFF Escrow not inhibited.
18 x COINCO Global 2 MDB (cat. B) – Second hand change giver
It’s a community-based project which helps to repair anything. Unplug ribbon cable from changer. If the price for one or more of the selections is set to zero, that selection is a free vend. If the coin stabilizer looks buckled, wrinkled or is not firmly adhered to the changer, replace it at this time. Installation and removal can stress the plastic, causing the shims to lose their ability to stay firmly in place.
Remove the screws from the bottom, exterior sides of the changer housing and remove payout base. Once you have entered ccoinco Display Mode, Inventory Buttons A through D are used to move through the addresses as follows: Press C again to view the lower four digits, including the decimal point if any. Cinco 8 for 4-Price Electromechanical 7. Once the tube reaches its float level in Standard Float Coincl, any coins normally routed to that tube will be sent to the cashbox.